DIY Ambilight with WS2812B, ESP32, and Hyperion

/ DIY Projects, ESP32, WLED

Create Your Own Ambilight System: Step-by-Step Guide with WS2812B LEDs and ESP32

This guide provides step-by-step instructions to create an Ambilight system for your TV using WS2812B LEDs, an ESP32, and Hyperion. Follow these steps to enjoy immersive lighting synchronized with your screen.

Materials Required

Step 1: Assemble the Hardware

1. Plan Your Layout

  • Measure the perimeter of your TV and cut the WS2812B LED strip to the required length (if necessary).
  • Place the strip around the back edges of the TV, ensuring the LED direction matches your planned wiring.
  • Choose a starting point for the LED strip (e.g., bottom center, bottom left) based on ease of cable management and software configuration. The starting position can influence both physical setup and how effects are displayed, so ensure this is set correctly in the software later. – Measure the perimeter of your TV and cut the WS2812B LED strip to the required length (if necessary).
  • Place the strip around the back edges of the TV, ensuring the LED direction matches your planned wiring.

2. Wire the Components

  • Power: Connect the LED strip’s +5V and GND to the 5V power supply. Ensure your power supply can handle the strip’s current requirements (each LED draws up to 60mA at full brightness).
  • Logic Level Shifter:
    • Connect the ESP32 GPIO pin (e.g., GPIO 2) to the logic level shifter’s 3.3V input.
    • Connect the 5V output of the logic level shifter to the LED strip’s DI (data input) pin.
  • Resistor: Solder a 330-470 ohm resistor in series with the data line to protect the LEDs and improve signal stability.
  • Capacitor: Place a 1000 µF capacitor across the +5V and GND terminals near the start of the LED strip to smooth power fluctuations.
  • Grounding: Ensure all components share a common ground (ESP32, power supply, and LED strip).

Step 2: Flash WLED on the ESP32

1. Download WLED Firmware

2. Flash the Firmware

3. Initial Configuration

  • Connect to the WLED Wi-Fi network (SSID: WLED-AP).
  • Access the WLED setup page at http://4.3.2.1.
  • Configure your home Wi-Fi network and save settings.

4. Set Up LED Strip in WLED

  • Enter the number of LEDs in your strip.
  • Set the GPIO pin for data (e.g., GPIO 2).
  • Configure the starting point of the LED strip to match its physical placement (e.g., bottom center, bottom left) to ensure effects align properly.
  • Save the settings.
  • Enter the number of LEDs in your strip.
  • Set the GPIO pin for data (e.g., GPIO 2).
  • Save the settings.

Step 3: Install and Configure Hyperion

1. Install Hyperion

  • Download and install Hyperion from hyperion-project.org on a device capable of running it (e.g., Raspberry Pi, Windows PC, or macOS).

2. Set Up Screen Capture

  • If using a USB HDMI capture device:
    • Connect the capture device to your source (e.g., TV’s HDMI output).
    • Configure the device in Hyperion to grab the screen feed.
  • Alternatively, set up software-based screen grabbing if supported by your system.

3. Configure Hyperion to Control WLED

  • In Hyperion’s LED Hardware Configuration:
    • Select WLED as the LED device.
    • Enter the IP address of the ESP32 running WLED.
    • Set the LED layout to match the strip placement on your TV.

Step 4: Fine-Tune and Test

1. Adjust Settings in Hyperion

  • Configure brightness, colors, and zone mapping to align with your TV dimensions.

2. Test the Setup

  • Play colorful videos or a movie to verify the Ambilight effects.

3. Optimize for Performance

  • Ensure minimal lag by tweaking Hyperion settings.
  • Keep firmware for WLED and Hyperion updated for the latest features.

Troubleshooting Tips

  • No Lights: Check power connections and ensure the ESP32 is outputting a signal.
  • Flickering LEDs: Verify the resistor is in place on the data line and the capacitor is installed across the power supply.
  • Wi-Fi Issues: Ensure the ESP32 is connected to the same network as your Hyperion device.

Share on:
Scroll to Top